whlat.blogg.se

1. WHAT PORT DOES WIRESHARK USE FULL
2. WHAT PORT DOES WIRESHARK USE PASSWORD
3. WHAT PORT DOES WIRESHARK USE WINDOWS 7
4. WHAT PORT DOES WIRESHARK USE WINDOWS

Display traffic with source or destination port as 443 tcp.port = 443ĥ. Display tcp and dns packets both tcp or dnsģ. Send it to: with a subject line of " Proj 6 From YOUR NAME", replacing "YOUR NAME" with your real name.1. Save the document with the filename " YOUR NAME Proj 6b", replacing "YOUR NAME" with your real name.Įmail the images to me as attachments to an e-mail message. Make sure the four required packets are visible This is a complete TCP three-way handshake, followed by a RST to end the session. The Info column should show this pattern of four packets, as shown below:

In the Wireshark Window, click Capture, Stop. Using Wireshark to Analyze the Connect Scan You should see one line of green text, showing port "135/tcp open", as shown above. Your command should match the image below, In the Zenmap window, select a Profile of " Intense scan, all TCP ports". Performing a Connect Scan of Port 135 only In the The Wireshark Network Analyzer window, click Capture, Start.If you see a message saying "Save capture file before starting a new capture?", click " Continue without saving". When the scan completes, you should see a list of open ports including "135/tcp open", as shown below. Select a Profile of " Quick Scan", as shown below on this page.

WHAT PORT DOES WIRESHARK USE WINDOWS

In the Zenmap window, enter the IP address of your Windows Performing an Quick Scan of the Windows Machine Because you are scanning your own LAN, Nmap uses ARP broadcasts rather than ICMP packets to find hosts. You should see a lot of ARP requests, as shown below on this page. In the Wireshark: Capture Window, click Capture, Stop. Using Wireshark to Analyze the Ping Sweep Save the document with the filename " YOUR NAME Proj 6a", replacing "YOUR NAME" with your real name. Type mspaint into the Search box and press the Enter key.Ĭlick in the untitled - Paint window, and press Ctrl+V on the keyboard. On the host machine, not the virtual machine, click Start.

WHAT PORT DOES WIRESHARK USE FULL

YOU MUST SUBMIT A FULL-SCREEN IMAGE FOR FULL CREDIT! That will copy the whole desktop to the clipboard. Press the PrintScrn key in the upper-right portion of the keyboard.

WHAT PORT DOES WIRESHARK USE WINDOWS 7

In the left pane of the Zenmap window, as shown above.Ĭlick the taskbar at the bottom of your host Windows 7 desktop, to make the host machine listen to the keyboard, instead of the virtual machine. Make sure at least two machines are visible The IP addresses and the total number of hosts may be different, but you should detect at least two hosts-your Linux and Windows machines. When the sweep completes, you should see a list of the hosts that were found on the left side of the Nmap window, as shown above. Zenmap Performing a Ping Sweep of your Network Check the "Don't show this message again" box and click the OK button. Press Ctrl+C to stopĪ box pops up warning you that wireshark is running as root. You should see lines saying "64 bytes from.". Kali Linux does not include Zenmap by default. When the ping is working properly, type Ctrl+C to stop the pinging. You should see lines saying "64 bytes from.", indicating that you do have a working network connection between the two machines. In the Terminal window, after the # prompt, enter this command, Pinging the Windows Machine From the Linux Virtual MachineĪt the upper left of your Linux desktop, click the little black square icon to open a Terminal window.

WHAT PORT DOES WIRESHARK USE PASSWORD

Launch your Linux virtual machine.When your machine starts up, log in as root with a password of toor. Click both of the " Turn off Windows Firewall (not recommended)" buttons, as shown below. On the left side of the "Windows Firewall" box, click " Turn Windows Firewall on or off". In the "Control Panel" section of the results, click " Windows Firewall". Make a note of that IP address.įrom your Windows desktop, click Start. In S214, it's the adapter with an IP address starting with "192.168.1". Several IP addresses appear.įind the adapter that goes to your LAN.

In the Command Prompt window, enter the IPCONFIG command and press the Enter key. In the search box, enter CMD and press the Enter key. Project 6: Analyzing a Port Scan (20 points) What You Need for This Projectįinding the IP Address of Your Windows Machine From your Windows desktop, click Start. Project 6: Analyzing a Port Scan (20 points)